Info / Download

The RangeExtender consists of a ground station and a Wi.232 receiver module for the MikroKopter.
This can be used to establish a wireless connection between a Windows PC or a Android tablet to the MikroKopter.
(Range up to 1000mtr)

This allows you to carry out wireless parameterization of the MikroKopter, transmit / monitor waypoints, or display the telemetry during a flight. (e.g. with Windows-MikroKopter-Tool or Android-KopterTool )

The ground station can be connected via USB or Bluetooth to a computer/tablet. The Wi.232 receiver modul will be connected to the MikroKopter.

• Shoplink : RangeExtender

  FTDI-driver : Download

Technical data / delivery

Delivery:

• 1x RangeExtender

• 1x Wi.232 Kopter
• 1x USB cabel

• 1x 4pol molex cable (for a Wi.232 V3.0 for FlightCtrl V3)

• 1x Ribbon cable with 2x 10 pin post connector (for a Wi.232 V2.0 for FlightCtrl V":X)

Technical data:

• Weight RangeExtender => 110g
  

• Weight Wi.232 Modul copter => 8g
  

• Wi.232 => 868.225MHz / 25mW

• Bluetooth => 2.4GHz / 2.51mW

• Data => 9600 Baud / 8N1

• Battery RangeExtender => 3,6V/800mAh NiMH Akku(AAA)
  

• Connection => USB or Bluetooth
  

• Charge => via USB (5V)
  

• Display for => Power, Charge, Rx/Tx, Bluetooth connection
  

• Battery life => 7-8 Stunden

• Bluetooth PIN => 0000

• Individual RE-ID => see "RE-ID" backside RangeExtender (required for the use of the MK-TabletTool)

Charge RangeExtender

Your RangeExtender includes a 3,6V/800mAh NiMH battery. With this battery the RangeExtender can work for some hours.
If the battery is used up, a warning signal sounds and the battery must be charged.

To charge the battery, connect the RangeExtender via the USB cable with a PC or a 5V-power supply (like you use for a mobil phone).
During the charging process the red LED Charge lights up. When the battery is fully charged, this LED goes off.
The charging process can takes several hours to complete charging.

The connection

You can use the RangeExtender with a:

• Windows Computer / Laptop / Tablet
• Android Tablet / Smartphone

If you use a Windows computer you can use the MikroKopter-Tool.
With this program you can configure the MikroKopter, see the telemetry of your copter and plan also a waypoint flight.

If you use a Android tablet you can use the KopterTool.
With this APP you can plan also a waypoint flight and see the telemetry of your copter.

Connection at the MikroKopter

The RangeExtender includes the Wi.232 modul for your MikroKopter.
This Wi.232 receiver module will be connected via a 4 wire Molex cable with the Update - UART connector of your FlightCtrl V3.

Alternatively the Wi.232 receiver module can also be connected to the serial port of the FlightCtrl V3.
For this you have to solder a 10-pin post socket to the Wi.232 receiving module.
So you can use the module also on older hardware (such as FlightCtrl V2.x, NaviCtrl).

Connection via Bluetooth or USB

You can use the RangeExtender via USB or Bluetooth.

• USB

  • Connect the USB cable with the RangeExtender and your Windows-PC.
    "Power ON" the RangeExtender with the switch.
    Now Windows should install the needed FTDI driver and the COM port for the RangeExtender automatically.
    
    If the automatic driver installation by Windows fails, the FTDI driver can be downloaded and manually installed here:
    FTDI-driver : Download
    
    

    For the connection to the MikroKopter the Windows program MikroKopter-Tool can be used.
    Information about usage can be found here: MikroKopter-Tool

• Bluetooth

  • "Power ON" the RangeExtender with the switch.
    Activate Bluetooth on the used device and start the "bluetooth scan".
    (see manual of the used device)
    In the list of detected devices should !Range extender appear. If not - start the scan again.
    The Bluetooth-Pin for the bluetooth device is 0000.
    After the RangeExtender is paired you can use it with the MikroKopter-Tool or the Android APP.
    if the connection via Bluetooth is OK the blue LED Bluetooth on your RangeExtender is ON.
    
    

    If the MikroKopter Android APP "KopterTool" is used to connect to the MikroKopter, the APP will require a "RE-ID".
    This individual ID can be found on the back of the RangeExtender.
    Information about the use of the APP can be found here: Android-KopterTool

Safety instructions / Intended use

To prevent short circuit, never expose this product to rain or moisture. Do not use near or near a bath, swimming pool, etc. Do not expose the components of your system to extremely high temperatures or strong light sources.
Never open the product! The device contains components which can be damaged by contact. Any manipulation of the battery can lead to serious injuries. Risk of fire! Do not heat, burn, short circuit or charge the battery with excessive or reverse polarity. The battery to be charged must stand on a non-flammable, heat-resistant and non-conductive surface during charging! Also, flammable or easily inflammable objects should be kept away from the charger. Batteries may only be charged under supervision. Incorrect treatment causes a risk of ignition, explosion, burns and burns. Suitable extinguishing media: water, CO2 , Sand. Leaking electrolyte is corrosive, do not bring into contact with skin or eyes. In case of emergency rinse immediately with plenty of water and seek medical attention.
Leave repairs or maintenance only to professionals.
In case of improper use, self-made modifications or self-made repairs, all warranty claims expire. HiSystems assumes no product liability in the event of misuse of the product or any other use of the product than its intended use. HiSystems assumes no liability for consequential damage other than statutory product liability.
Only connect the USB adapter to a power supply / PC / laptop, etc., after checking that the voltage matches the voltage specified in the technical data. Never connect a power adapter or power cord if they are damaged. In this case, contact your supplier.
This product is not a toy. Keep out of reach of children.

Conformity