#acl AdminGroup:read,write,revert EditorsGroup:read,write,revert All:read

##############################################################################
##############################################################################

## DE-EN_Sprachflaggen

{{{#!wiki language_selector/de
[[ de/EasyOkto | {{ http://www.mikrokopter.de/addons/shared_addons/themes/mk3/img/flag_ger.png }}]]
}}}

###########################################################################
<<BR>>
<<BR>>
<<BR>>
<<BR>>
<<TableOfContents>>
<<BR>><<BR>>
###########################################################################
###########################################################################
<<BR>>



= Info =

For the construction of your new ''MK EASY Okto V3'' you only need a cross- and a flathead screwdriver. <<BR>> 
Solderings are not required. All components can be bolted and / or plugged.

Please read this page '''before''' you start to assemble your copter!

This is an electronic flight instrument. A careful and accurate building assures you a flawless function and much joy with your new !MikroKopter.


##############################################################################
##############################################################################
<<BR>><<BR>><<BR>><<BR>><<BR>><<BR>>










= Step 1 - The arms =

##----------------------------------------------------------------------------
## Bild rechts: Ausleger + fertige Centerplate
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Ausleger_Okto.jpg?m=1543247073 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Ausleger_Okto.jpg?m=1543247073 }} ]]

[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Centerplate.jpg?m=1543247148 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Centerplate.jpg?m=1543247148 }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step1 - Die Ausleger

The eight riggers can be mounted in the pre-assembled Center Plate.  <<BR>><<BR>>

What is needed:

 * 1x rigger 460mm - red with LED
 * 3x rigger 460mm - black
 * 2x rigger 355mm - black with LED
 * 2x rigger 355mm - black
 * 16x screw M3x16 (metal)
 * 12x self locking nut M3 (metal)
 * 4x dampener M3x15

 * 12x screw M3x16 black (plastic)
 * 12x Hex nut M3 black (plastic)

##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
##{{{#!html
##<div style="clear:both">
##}}}
##----------------------------------------------------------------------------
<<BR>><<BR>><<BR>><<BR>><<BR>><<BR>><<BR>>




##############################################################################
----



##----------------------------------------------------------------------------
## Bild rechts: Rahmen + Schraublöcher Ausleger + Montagelöcher Centerplate
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Rahmen-Ausleger.jpg?m=1543247278 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Rahmen-Ausleger.jpg?m=1543247278 }} ]]
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Ausleger_Schraubl%C3%B6cher.jpg?m=1543247074 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Ausleger_Schraubl%C3%B6cher.jpg?m=1543247074 }} ]]

[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Centerplate-Montage_Okto_Muttern_Daempfer.jpg?m=1543247150 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Centerplate-Montage_Okto_Muttern_Daempfer.jpg?m=1543247151 }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step1 - Die Ausleger
<<BR>>

On the first image you can see how to mount the single arms into the Centerplate (please note - the motors and the labeling of the centerplate points upwards). Please note the arrangement of the boom in the first image. <<BR>>

Use two metal screws (M3x16) to fix the riggers. In the second picture you can see which holes are used.

'''Important:''' Insert the metal screws from the '''bottom''' of the Centerplate.

At the top you fix 4 screws with a self locking metal nut (M3). <<BR>>
On the 4 points where you see the circle (blue in the picture) on the top, you use a dampener to fix the screws (M3x15).

##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
{{{#!html
<div style="clear:both">
}}}
##----------------------------------------------------------------------------
<<BR>><<BR>>



##############################################################################
----



##----------------------------------------------------------------------------
## Bild rechts: Montage Ausleger
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Ausleger_Step1.jpg?m=1543247075 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Ausleger_Step1.jpg?m=1543247075 }} ]]
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Ausleger_Step2.jpg?m=1543247109 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Ausleger_Step2.jpg?m=1543247109 }} ]]

[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Ausleger_Step3.jpg?m=1543247110 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Ausleger_Step3.jpg?m=1543247110 }} ]]
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Ausleger_Step4.jpg?m=1543247111 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Ausleger_Step4.jpg?m=1543247111 }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step1 - Die Ausleger
<<BR>>

Please take care that you will not hurt or cut the cables.

##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
{{{#!html
<div style="clear:both">
}}}
##----------------------------------------------------------------------------
<<BR>><<BR>>



##############################################################################
----



##----------------------------------------------------------------------------
## Bild rechts: Kunststoffschrauben an Ausleger
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Centerplate-Montage_Okto_Ausleger.jpg?m=1543247149 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Centerplate-Montage_Okto_Ausleger.jpg?m=1543247149 }} ]]
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Montage-Kuststoffschrauben.jpg?m=1543247206 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Montage-Kuststoffschrauben.jpg?m=1543247206 }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step1 - Die Ausleger
<<BR>>

At the edge of centerplate, the long riggers can be fixed with 2 plastic screws and nuts. <<BR>>
The short riggers, each with a single plastic screws / nuts. Through the free holes later the 4 metal screws are inserted. The battery holder is attached to the 4 metal screws.

'''Important:''' Insert the plastic screws from the '''bottom''' of the Centerplate (see pictures).

##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
{{{#!html
<div style="clear:both">
}}}
##----------------------------------------------------------------------------
<<BR>><<BR>>



##############################################################################
----



##----------------------------------------------------------------------------
## Bild rechts: Ausleger fertig in Centerplate
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Ausleger_Step5.jpg?m=1543247111 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Ausleger_Step5.jpg?m=1543247111 }} ]]
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Ausleger_Step6.jpg?m=1543247112 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Ausleger_Step6.jpg?m=1543247112 }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step1 - Die Ausleger
<<BR>>

When all eight riggers inserted and screwed the frame should look like this.

##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
{{{#!html
<div style="clear:both">
}}}
##----------------------------------------------------------------------------



##############################################################################
##############################################################################
<<BR>><<BR>><<BR>><<BR>><<BR>><<BR>>










= Step 2 - Mounting BL-distributor =

##----------------------------------------------------------------------------
## Bild rechts: Verteiler + Rahmen fertig
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/BL-Ctrl_V3_Okto.jpg?m=1543247113 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/BL-Ctrl_V3_Okto.jpg?m=1543247113 }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step2 - Der BL-Verteiler

In the next step the BL-distributor is mounted on the frame. <<BR>><<BR>>

What is needed:

 * 1x BL-distributor
 * 8x screw M3x8 black (plastic)
 * 1x cable ties 3,5mm x 110mm (long)

##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
{{{#!html
<div style="clear:both">
}}}
##----------------------------------------------------------------------------
<<BR>><<BR>>



##############################################################################
----



##----------------------------------------------------------------------------
## Bild rechts: Kunststoffschrauben an Ausleger
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Montage-BL-Ctrl-Okto_1.jpg?m=1543247151 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Montage-BL-Ctrl-Okto_1.jpg?m=1543247151 }} ]]
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Montage-BL-Ctrl-Okto_2.jpg?m=1543247202 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Montage-BL-Ctrl-Okto_2.jpg?m=1543247202 }} ]]

[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Centerplate-Montage_Okto_Muttern_BL-Ctrl.jpg?m=1543247150 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Centerplate-Montage_Okto_Muttern_BL-Ctrl.jpg?m=1543247150 }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step2 - Der BL-Verteiler
<<BR>>

The !LiPo cable is guided through the recess (beside the buzzer) as you can see in the picture.

'''Important:''' The arrow of the PCB is pointing to the red rigger #1.

Fix the BL-distributor with the 8 plastic screws on the frame.<<BR>>

##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
{{{#!html
<div style="clear:both">
}}}
##----------------------------------------------------------------------------
<<BR>><<BR>>



##############################################################################
----



##----------------------------------------------------------------------------
## Bild rechts: BL mit Kabelbinder
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Montage-BL-Ctrl-Okto_3.jpg?m=1543247203 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Montage-BL-Ctrl-Okto_3.jpg?m=1543247203 }} ]]
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Montage-BL-Ctrl-Okto_4.jpg?m=1543247203 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Montage-BL-Ctrl-Okto_4.jpg?m=1543247204 }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step2 - Der BL-Verteiler
<<BR>>

After the BL-distributor is attached, the !LiPo connecting cable can be fixed with cable ties to the frame.

'''Important:''' As you can see in the pictures, the !LiPo cable __must__ be twisted. This prevents compass error!<<BR>><<BR>>

##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
{{{#!html
<div style="clear:both">
}}}
##----------------------------------------------------------------------------



##############################################################################
##############################################################################
<<BR>><<BR>><<BR>><<BR>><<BR>><<BR>>










= Step 3 - Connection to the BL-distributo =

In the next step we can connect the buzzer, the LED's and the motors with the BL-distributor. <<BR>><<BR>>

##############################################################################
----

##----------------------------------------------------------------------------
## Bild rechts: Anschluss Summer
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Anschluss-Okto-Board-Summer.jpg?m=1543247073 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Anschluss-Okto-Board-Summer.jpg?m=1543247073 }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step3 - Anschluss an den BL-Verteiler

'''~+Buzzer+~''' <<BR>>

Connect the buzzer with the lateral contact at the BL-distribution. Take care about the direction (see picture).

The buzzer will give no sound if it is plugged in the wrong direction.

##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
{{{#!html
<div style="clear:both">
}}}
##----------------------------------------------------------------------------
<<BR>><<BR>>



##############################################################################
----



##----------------------------------------------------------------------------
## Bild rechts: Anschluss LED
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Anschluss-Okto-Board-LED.jpg?m=1543247070 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Anschluss-Okto-Board-LED.jpg?m=1543247071 }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step3 - Anschluss an den BL-Verteiler

'''~+LED+~''' <<BR>>

Connect the LED cables at the BL-distribution.Take care about the direction (see picture)

A wrong connected LED will not work.

Info: <<BR>> 
After you connect the !LiPo the LEDs on the short black riggers are ON. <<BR>> 
The LEDs on the red (front) rigger are connected to the switching output "EXT1 (L)" of the !FlightCtrl. So this LEDs are also ON, but if there is e.g. a battery warning the LEDs will flash fast.

##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
{{{#!html
<div style="clear:both">
}}}
##----------------------------------------------------------------------------
<<BR>><<BR>>



##############################################################################
----



##----------------------------------------------------------------------------
## Bild rechts: Anschluss Motor
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Anschluss-Okto-Board-Motor.jpg?m=1543247072 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Anschluss-Okto-Board-Motor.jpg?m=1543247072 }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step3 - Anschluss an den BL-Verteiler

'''~+Motor+~''' <<BR>>

The direction of rotation of the motor is determined by the plug-order of three cables. <<BR>> 
On the BL-distribution board, the plug-in sequence (Color) is printed:

 * 1,3,5,7 => A=gray, B=blue, C=black (left rotating propeller)
 * 2,4,6,8 => A=blue, B=gray, C=black (right rotating propeller)

(Declaration of propeller rotation direction: see below under [[#Sprung1|propeller]].)

'''TIP:''' If the propeller rotation direction is wrong, change only 2 of the 3 cables to change the rotation direction.


##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
{{{#!html
<div style="clear:both">
}}}
##----------------------------------------------------------------------------



##############################################################################
##############################################################################
<<BR>><<BR>><<BR>><<BR>><<BR>><<BR>>










= Step 4 - mounting FlightCtrl + MKGPS =

##----------------------------------------------------------------------------
## Bild rechts: FC+GPS
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/MK-Baugruppen/FlightCtrl/FlightCtrl-V3.0/FC_V3.jpg | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/MK-Baugruppen/FlightCtrl/FlightCtrl-V3.0/FC_V3.jpg }} ]]

[[ http://gallery3.mikrokopter.de/var/albums/intern/MK-Baugruppen/MKGPS/MK-GPS_V4/GNSS_V4.jpg | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/MK-Baugruppen/MKGPS/MK-GPS_V4/GNSS_V4.jpg }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step4 - Montage FlightCtrl + MKGPS

NNow the !FlightCtrl and MKGPS can be mounted. <<BR>><<BR>>

What is needed:

 * 8x spacers M3x15 schwarz (plastic)
 * 4x hex nut M3 black (plastic)
 * 2x 5pol Molex cabel
 * 1x 4pol Molex cabel
##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
{{{#!html
<div style="clear:both">
}}}
##----------------------------------------------------------------------------
<<BR>><<BR>>



##############################################################################
----



##----------------------------------------------------------------------------
## Bild rechts: Anschluss FlightCtrl
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Okto-Montage_FC_Step1.jpg?m=1543247246 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Okto-Montage_FC_Step1.jpg?m=1543247246 }} ]]
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Okto-Montage_FC_Step2.jpg?m=1543247247 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Okto-Montage_FC_Step2.jpg?m=1543247247 }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step4 - Montage FlightCtrl + MKGPS

'''~+!FlightCtrl+~''' <<BR>>

On each dampener install first plastic spacers M3x15. On this spacers we mount the !FlightCtrl and fix it with a plastic spacers M3x15.

'''Important:''' The arrow of the !FlightCtrl is pointing to the red arm #1. 

Both cables of the !FlightCtrl for the receiver are guided through the recess of the Center Plate (see picture).

After the !FlightCtrl is fixed we can connect it with the 5pol molex cable with the BL-distribution. <<BR>>
The gray cable of the BL-distribution must be connected now with the switching output (L) of the !FlightCtrl (upper left pin - see picture).

Connect the small '''Tiny Servo Adapter''' with the molex connection ''SERVO'' on the !FlightCtrl. The adapter is also guided through the recess of the Center Plate (see picture).<<BR>>
On the ''Tiny Servo Adapter'' you can connect later e.g. a camera mount (Nick + Roll)
<<BR>><<BR>>


More informations about the !FlightCtrl you can find here: '''[[en/FlightCtrl_V3.0|FlightCtrl_V3.0]]'''


##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
{{{#!html
<div style="clear:both">
}}}
##----------------------------------------------------------------------------
<<BR>><<BR>>



##############################################################################
----



##----------------------------------------------------------------------------
## Bild rechts: Anschluss GPS
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Okto-Montage_FC_Step3.jpg?m=1543247247 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Okto-Montage_FC_Step3.jpg?m=1543247248 }} ]]
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Okto-Montage_FC_Step4.jpg?m=1543247248 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Okto-Montage_FC_Step4.jpg?m=1543247248 }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step4 - Montage FlightCtrl + MKGPS

'''~+MKGPS+~''' <<BR>>

Connect the MKGPS now with a
 * 5pol Molex cabel - to the Master GPS-Port
 * 4pol Molex cabel - to the Master Compass-Port

Connect then the other side of the molex cables with the GPS and Compass connections on the !FlightCtrl.

If this is done you can place the MKGPS on top of the plastic spacers and fix it wit 4 plastic nuts.

'''Important:''' The arrow and the LED of the MKGPS are pointing to the red arm #1.


##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
{{{#!html
<div style="clear:both">
}}}
##----------------------------------------------------------------------------




##############################################################################
##############################################################################
<<BR>><<BR>><<BR>><<BR>><<BR>><<BR>>










= Step 5 - mounting LiPo-holder =

The !LiPo-holderis a safe place for the !LiPo's under the copter.

In the already assembled !LiPo-holder you can place 1x !LiPo.<<BR>>

What is needed:

 * 4x screw M3x16 (metal)


##############################################################################
----


##----------------------------------------------------------------------------
## Bild rechts: Distanzhülsen+Schrauben
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Centerplate-Montage_Okto_Akkuhalter.jpg?m=1543247149 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Centerplate-Montage_Okto_Akkuhalter.jpg?m=1543247149 }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step5 - Montage LiPo-Halter
<<BR>>

At the 4 marked locations (see picture) insert the 4 metal screws from above through the mounting holes of the Center Plate.

##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
{{{#!html
<div style="clear:both">
}}}
##----------------------------------------------------------------------------
<<BR>><<BR>>



##############################################################################
----


##----------------------------------------------------------------------------
## Bild rechts: LiPo-Halter unter Centerplate
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Okto-Montage_Akkuhalter1.jpg?m=1543247245 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Okto-Montage_Akkuhalter1.jpg?m=1543247245 }} ]]
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Okto-Montage_Akkuhalter2.jpg?m=1543247246 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Okto-Montage_Akkuhalter2.jpg?m=1543247246 }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step5 - Montage LiPo-Halter
<<BR>>

Now you can place the !LiPo-holder under the Centerplate and fix it with the 4 metal screws.

'''Important:''' The side with the Velcro fastener toward the left side - there where the !LiPo cable is.

##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
{{{#!html
<div style="clear:both">
}}}
##----------------------------------------------------------------------------




##############################################################################
##############################################################################
<<BR>><<BR>><<BR>><<BR>><<BR>><<BR>>










= Step 6 - mounting landing gear =

The landing gear is now attached to the 4 short riggers.<<BR>>

What is needed:

 * 4x landing gear "MK HiLander-26"


##############################################################################
----


##----------------------------------------------------------------------------
## Bild rechts: Schrauben für Landegestell in Centerplate
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Montage-HiFlexlander_2.jpg?m=1543247205 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Montage-HiFlexlander_2.jpg?m=1543247205 }} ]]
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Montage-HiFlexlander_1.jpg?m=1543247204 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Montage-HiFlexlander_1.jpg?m=1543247204 }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step6 - Montage Landegestell
<<BR>>

The 4 "MK HiLander-26" are attached to the 4 short riggers. 

The assembly is described in the second diagram.

##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
{{{#!html
<div style="clear:both">
}}}
##----------------------------------------------------------------------------





##############################################################################
##############################################################################
<<BR>><<BR>><<BR>><<BR>><<BR>><<BR>>










= Step 7 - mounting cover =

To protect the electronics, the hood is mounted.<<BR>>

What is needed:

 * 1x cover
 * 4x tapping screw


##############################################################################
----


##----------------------------------------------------------------------------
## Bild rechts: Schrauben in Haube
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Rahmen-Haubenbefestigung.jpg?m=1543247278 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Rahmen-Haubenbefestigung.jpg?m=1543247278 }} ]]
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Rahmen-Haubenbefestigung2.jpg?m=1543247279 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Rahmen-Haubenbefestigung2.jpg?m=1543247279 }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step7 - Montage Haube
<<BR>>

The cover is placed on top of the frame. The holes for the tapping screws mus point to the left and right side.

Fix now the cover with the tapping screws on the frame. 


##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
{{{#!html
<div style="clear:both">
}}}
##----------------------------------------------------------------------------






##############################################################################
##############################################################################
<<BR>><<BR>><<BR>><<BR>><<BR>><<BR>>








<<Anchor(Sprung1)>>

= Step 8 - mounting propeller =


##----------------------------------------------------------------------------
## Bild rechts: Montage Propeller + Drehrichtung
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/EasyKopter/EasyOkto/Rahmen-Propeller.jpg?m=1543247279 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/EasyKopter/EasyOkto/Rahmen-Propeller.jpg?m=1543247280 }} ]]
[[ http://gallery3.mikrokopter.de/var/albums/intern/sonstiges/MK-Montage/Montage-Propeller.jpg | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/sonstiges/MK-Montage/Montage-Propeller.jpg }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step8 - Montage Propeller
<<BR>>

Finally, the propellers are screwed. Here please take care of the direction of rotation..

Use on the long riggers / motor the '''left turning Propeller''', <<BR>> 
and on the short riggers / motor the '''right turning Propeller'''.


##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
{{{#!html
<div style="clear:both">
}}}
##----------------------------------------------------------------------------
<<BR>><<BR>>




##############################################################################
----


##----------------------------------------------------------------------------
## Bild rechts: Drehrichtung
{{{#!html
<div style="float: right; margin: 20px;">
}}}
[[ http://gallery3.mikrokopter.de/var/albums/intern/sonstiges/MK-Montage/Propeller-Drehrichtung-Links.jpg?m=1539159956 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/sonstiges/MK-Montage/Propeller-Drehrichtung-Links.jpg?m=1539159956 }} ]]
[[ http://gallery3.mikrokopter.de/var/albums/intern/sonstiges/MK-Montage/Propeller-Drehrichtung-Rechts.jpg?m=1539159957 | {{ http://gallery3.mikrokopter.de/var/thumbs/intern/sonstiges/MK-Montage/Propeller-Drehrichtung-Rechts.jpg?m=1539159957 }} ]]
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

## Beschreibung Step8 - Montage Propeller
<<BR>>

Here you can see the direction of rotation of the propeller.


##----------------------------------------------------------------------------
## Infotext: Aufheben des "Float" Befehl damit nachfolgende Eintragungen in neuer Zeile beginnen.
{{{#!html
<div style="clear:both">
}}}
##----------------------------------------------------------------------------
<<BR>><<BR>>




##############################################################################
##############################################################################
<<BR>><<BR>><<BR>><<BR>><<BR>><<BR>>



= Step 9 - Ready =

Now that everything has been mounted, your copter should look like this here.

Congratulations. :D 

The assembling of your Easy copter is done. 

We continue now with the setting and he first set up your new !MikroKopter.

 {{ http://gallery3.mikrokopter.de/var/resizes/intern/EasyKopter/EasyOkto/Okto-fertig.jpg?m=1543308379 }}






##############################################################################
##############################################################################
<<BR>><<BR>><<BR>><<BR>><<BR>><<BR>>










= First commissioning =

After your !MikroKopter is assembled you can download the latest Software for your copter here: 

 * '''[[en/download|Software-Download]]'''
 * '''[[en/SoftwareUpdate|how to update]]'''
 * '''[[en/SbS|Setup]]'''

##############################################################################
##############################################################################
<<BR>><<BR>><<BR>><<BR>><<BR>><<BR>>










= Safety =

A Copter can also be dangerous. The confidence in dealing with the copter comes first, so read carefully:

 * SafetyFirst
 * [[en/LiPo|LiPo]]